01
Join the two sections
Align the two aluminum sections and connect them with the included hardware. Start every fastener before final tightening.
HEMSK DAYS
Product support / US
MOLLE panel / installation system
Install it right. Carry with confidence.
Choose your mounting system first. The hardware at the top of your panel determines which guide and video to follow.
Watch installation video
Type A / flexible upper strap
V1 Strap Mount
A no-drill two-section aluminum panel secured with an upper headrest-area strap and a separate lower seat-back strap.
- 1-seat kit
- 15 × 24.5 IN
- 2 MM ALUMINUM
- No-drill strap mount
Type B / sliding metal headrest mount
V2 Pro Bracket Mount
A more rigid mounting system for seats with separate headrest posts, using adjustable top brackets and a lower stabilizer.
- 1-seat kit
- Sliding top mount
- 2 MM ALUMINUM
- Lower stabilizer
01 / Video
Start with the quick install video.
Watch the complete guide once before tightening any hardware. Pause at each step and confirm your panel matches the version shown.Included membership card
Register your card.
Enter the number printed on your HEMSK DAYS membership card and the email you want connected to it.02 / Seat fit
Check your seat before installing.
A universal panel still needs a clear strap or bracket path. Do not force hardware onto an incompatible seat.Compatible when
- The seat back is wide enough for the 15-inch panel.
- There is a clear route around the headrest area for the upper strap.
- The long lower strap can wrap around the seat without crossing controls or moving parts.
Not compatible when
- There is no safe upper or lower strap path.
- The panel or straps would cover airbags, controls, latches or seat mechanisms.
- Installed gear would contact a rear passenger or prevent safe seat movement.
Compatible when
- The seat has two separate, exposed headrest posts.
- The sliding brackets can align with both posts without being forced.
- The seat back is wide and firm enough for the panel and lower stabilizer.
Not compatible when
- The seat uses a one-piece fixed headrest or bucket-seat design.
- The panel or straps would cover airbags, controls, latches or seat mechanisms.
- Installed gear would contact a rear passenger or prevent safe seat movement.
Keep airbags, seat controls, latches and moving mechanisms clear. If the fit is uncertain, stop and contact support before driving.
03 / Parts
Count every part before you start.
One box contains one complete kit for one seat. For both front seats, order quantity two.
- ×2Aluminum panel sections
- ×1Complete hardware kit with hex key
- ×2Seat mounting straps — 1 long + 1 short
- ×1Heavy-duty accessory hook
- ×2Bungee cords
- ×2Hook-and-loop gear straps
- ×2Aluminum panel sections
- ×1Complete hardware kit with hex key
- ×1Extended lower seat strap
- ×2Sliding metal top brackets
- ×1Bottom metal stabilizer assembly
- ×2Bungee cords
- ×2Hook-and-loop gear straps
Pouches, tools and gear shown in lifestyle photos are not included.
04 / Install steps
Four steps. No drilling.
Use these images as a quick reminder. The installation video above is the primary guide for hardware orientation and strap routing.
02
Attach the upper strap
Secure the short strap to the upper mounting points and route it around the headrest area as shown in Video 1.
03
Wrap the lower strap
Center the panel, route the long strap around the seat back, connect the buckle and tension it evenly.
04
Tension, check, then load
Press all four corners, confirm every fastener is seated, then load gear evenly. Recheck after the first drive and periodically after that.
01
Join the panel
Connect both aluminum sections with the included fasteners. Keep the panel flat while tightening.
02
Align the sliding brackets
Loosely install both top brackets and slide them until they align with the two separate headrest posts.
03
Install the lower stabilizer
Follow Video 2 to secure the top mount, lower stabilizer and seat strap without contacting upholstery or controls.
04
Tension, check, then load
Press all four corners, confirm every fastener is seated, then load gear evenly. Recheck after the first drive and periodically after that.
05 / FAQ
Answers before the next drive.
Does one box cover both front seats?
No. Each box is one complete kit for one seat. Order quantity two for both front seats.
Are pouches and accessories included?
No. Pouches, tools and other gear shown in lifestyle images are display examples unless specifically listed in the parts checklist.
Is the panel rated to carry 80 lb while driving?
No vehicle-in-motion load rating is stated. The listing image shows a controlled stationary bench test. Braking, road conditions, gear shape, retention and strap tension all change safety in a moving vehicle.
Will the panel reduce rear-passenger space?
The empty 2 mm panel follows the seat back, but mounted gear adds depth. Remove or reposition bulky items before a rear passenger uses the seat.
Why is my panel moving or rattling?
Stop and check panel fasteners, bracket alignment, strap tension and every contact point. Type B users should also confirm the lower stabilizer is installed as shown in Video 2.
Can I use any MOLLE accessory?
The slots follow common MOLLE/PALS spacing, but accessory fit and retention vary. Secure every item for vehicle use and keep heavy or protruding objects away from passengers.
06 / Missing parts